CORALVOLT 24V 40VA HVAC Transformer, Multi-Tap 120/208/240V Input
Clearly labeled, color coded lead wires support straightforward installation. Input leads are WHT, BLK, RED, and ORG, and the 24V output leads are RED and GRN.
BE151840GDD HT01BC115-A BASLER TRANSFORMER 120V Stepdown 24V
Basler 24v Furnace Transformer BE111640GDD BE151840GDD BE112640GDD HT01BC115
This unit was removed in good working order from a functional furnace.
Basler Transformer BE151840GDD; HT01BC115-A; *Pre-Owned*
Specifications: – BE151840GDD; HT01BC115-A. It was in working condition when removed. Warranty: – ( just DOA only ).
Basler Electric BE151840GDD 120V to 24VAC 40VA Transformer HT01BC115-A Tested
Model: BE151840GDD. Manufacturer: Basler Electric. Secondary Output: 24VAC. ID No.: 001 G19.
Basler Electric BE151840GDD HVAC furnace transformer
It is a component commonly used in but not limited to Carrier furnaces. Part Numbers 322666-701, HT01BC115-A, BE151840GDD. Manufacturer Basler Electric. The primary wires are typically black and white, while the secondary wires are blue and red.
2pcs TP4056 5V 1A Micro USB 18650 Lithium Battery Charging and Protection Board
Dual Function: 1) Charge lithium cells from a 5V power source 2) Protect battery from over-discharge and over-currentCharge input: 5V DC • Maximum charge current: 1000mA • Charge cut-off: 4.2VDischarge protection cut-off: 2.5V • Over-current protection cut-off: 3AMicro-USB input • Size: 2.6×1.7cmThis is an enhanced USB-powered module for charging rechargeable lithium batteries using the constant-current/constant-voltage (CC/CV) charging method.This module provides constant-current/constant-voltage (CC/CV) charging, along with protection against over-voltage, over-discharge, over-current and short circuits to protect the battery and the device that it is powering.The device to be powered by the battery is connected to the module’s OUT+ and OUT- connectors and the battery is connected to the B+ and B- connections. When connected to USB power, the module provides up to 1A charge current until the battery is charged, then switches to a constant voltage mode to keep it charged.During use, if the battery voltage drops below about 2.4V, the DW01A protection IC disconnects the battery from the OUT connectors, disabling discharge to protect the battery from running at too low and self-destructing.When the module is then connected to USB power, it will trickle charge the battery to 2.9V (the over-discharge release voltage), at which point the charge current will be linearly increased to 1A maximum and the module will reconnect the battery to the OUT connections, allowing discharge of power from the battery to a connected load. Although the module cuts output power from the battery during an over-discharge situation, it still allows trickle charging of the battery to occur.The module also protects against overcurrent and short-circuit protection – it will cut the output from the battery if the discharge rate exceeds 3A or if a short-circuit condition occurs.This module is perfect for charging single cell 3.7V 1 Ah or higher LiPo cells such as 16550s and 18650s that don’t have their own protection circuit. It can charge two cells in parallel, however since the two cells share the charging current, they take twice as long to charge as a single cell.
Square D 3S1F 3 kVA Single Phase General Purpose Transformer 240x480V to 120/240
Phase: Single Phase. Built with high-quality Square D / Schneider Electric standards for long-lasting performance. Frequency: 60 Hz. Enclosure: NEMA 3R (rainproof – suitable for indoor/outdoor use).
1x LM317 Adjustable Voltage Linear Regulator Step Down Module AC/DC to 5/12/ 24V
The LM317 integrates multiple protection circuits such as overload protection and safe area protection. The LM317 does not require an external capacitor, unless the connection between the input filter capacitor.
12V To 9V 1.7A 15W DC-DC Step Down Converter DC Power Supply Module Waterproof
12V Input to 9V Output 1.7A 15W DC-DC Step-Down Power Converter DC Power Supply Module WaterproofThis miniature DC-DC step-down converter module converts a 10V to 24V (perfect for 12V automotive) DC input to 9V DC output at up to 1.7A current (15W maximum).Specifications:Epoxy sealed waterproof housingLightweight, compact, convenient to use and transportNon-isolatedWith overload / over-current / over / low voltage protection, stable performanceAuto recoveryInput voltage: DC 12V nominal, will operate on any input voltage from 10V to 24V DCQuiescent input current (no load attached): 96%Size (L x W x H): 38 * 27 * 23 mm (Length including mounting tabs is 52mm)Weight: 30gCase color: WhiteCable length: 12cm (approx)Operating Notes:As with any DC-DC converter, the input DC power supply powering this converter must be capable of providing the maximum power drawn by your load. If the input supply is not capable of providing the power, the converter will fold back the output voltage as necessary. Example: If your load draws 1.7A at 9V (15W), and the input supply is only capable of providing 12V at 1/2A (6W), the maximum output voltage the converter will deliver is 3.5V (6W/1.7A).The inputs and outputs are labeled on the sticker on top of the converter, the red and black wires are the + and – 12V input, and the red and yellow wires are the + and – 9V output. Package includes:1X 12V to 9V 1.7A Mini DC-DC Step Down ConverterContact us for quantity/OEM pricing.Get it faster! Stocks and ships from our US Colorado office for quick deliveryWe provide FREE USPS First Class Shipping with Tracking – Not Economy Shipping